View BD48K41G-TR_8870130.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

datasheet 2/15 bd48xxx series bd49xxx series tsz02201-0r7r0g300030-1- 2 ? 2013 rohm co., ltd. all rights reserved. 22.may.2013.rev.008 www.rohm.com tsz22111 ? ? connection diagram ssop5 vsof5 pin descriptions ssop5 vsof5 pin no. symbol function pin no. symbol function 1 v out reset output 1 v out reset output 2 v dd power supply voltage 2 sub substrate* 3 gnd gnd 3 n.c. unconnected terminal 4 n.c. unconnected terminal 4 gnd gnd 5 n.c. unconnected terminal 5 v dd power supply voltage *connect the substrate to gnd. ssop3(1pin gnd) ssop3(3pin gnd) pin descriptions ssop3-1 ssop3-2 pin no. symbol function pin no. symbol function 1 gnd gnd 1 v out reset output 2 v out reset output 2 v dd power supply voltage 3 v dd power supply voltage 3 gnd gnd ordering information note: when ordering new ssop5, select ?e? for package 1 and ?g? for package 2. lot. no top view v out sub n.c v dd gnd 4 3 2 1 5 marking lot. no top view v out v dd gnd n.c. n.c. marking 1 2 3 2 gnd v out v dd marking lot. no top view 1 2 3 v out v dd gnd marking lot. no top view part output type package1 reset voltage value package2 packaging and number 48 : open drain 23 : 2.3v forming specification 49 : cmos 0.1v step embossed tape and reel 60 : 6.0v tr :the pin number 1is the upper right :ssop5 :vsof5 tl :the pin number 1is package1 package2 package name the upper left e g ssop5 :ssop3-1 k g ssop3(1pin gnd) :ssop3-2 l g ssop3(3pin gnd) blank fve vsof5 blank g ssop5 r x x x x b d x x - t
datasheet 3/15 bd48xxx series bd49xxx series tsz02201-0r7r0g300030-1- 2 ? 2013 rohm co., ltd. all rights reserved. 22.may.2013.rev.008 www.rohm.com tsz22111 ? ? ssop5 2.90.2 0.13 4 + 6 -4 1.6 2.80.2 1.10.05 0.050.05 +0.2 -0.1 +0.05 -0.03 0.42 +0.05 -0.04 0.95 5 4 1 2 3 1.25max. 0.2min. 0.1 direction of feed reel * order quantity needs to be multiple of the minimum quantity. embossed carrier tape tape quantity direction of feed th e direction is th e 1 p in of p rodu ct i s a t th e upper ri gh t wh en you hol d reel on th e l eft hand a nd you pull ou t th e tape on th e ri gh t hand 3000pcs tr ( ) 1pin (unit : mm) vsof5 1.2 0.05 4 3 1.0 0.05 1 0.6max 0.22 0.05 0.5 5 1.6 0.05 0.13 0.05 0.2max 2 1.6 0.05 ( max 1.28 include bu rr) ssop3 2.92 l
datasheet 4/15 bd48xxx series bd49xxx series tsz02201-0r7r0g300030-1- 2 ? 2013 rohm co., ltd. all rights reserved. 22.may.2013.rev.008 www.rohm.com tsz22111 ? ? lineup table 1. lineup for vsof5 and ssop5 package package type vsof5 or ssop5 ssop5 output type open drain cmos open drain cmos detection voltage marking part number marking part number marking part number marking part number 6.0v ew bd4860 gw bd4960 cm bd48e60 ff bd49e60 5.9v ev bd4859 gv bd4959 ck bd48e59 fe bd49e59 5.8v eu bd4858 gu bd4958 ch bd48e58 fd bd49e58 5.7v et bd4857 gt bd4957 cg bd48e57 fc bd49e57 5.6v es bd4856 gs bd4956 cf bd48e56 fb bd49e56 5.5v er bd4855 gr bd4955 ce bd48e55 fa bd49e55 5.4v eq bd4854 gq bd4954 cd bd48e54 ey bd49e54 5.3v ep bd4853 gp bd4953 cc bd48e53 er bd49e53 5.2v en bd4852 gn bd4952 cb bd48e52 ep bd49e52 5.1v em bd4851 gm bd4951 ca bd48e51 en bd49e51 5.0v el bd4850 gl bd4950 by bd48e50 em bd49e50 4.9v ek bd4849 gk bd4949 br bd48e49 ek bd49e49 4.8v ej bd4848 gj bd4948 bp bd48e48 eh bd49e48 4.7v eh bd4847 gh bd4947 bn bd48e47 eg bd49e47 4.6v eg bd4846 gg bd4946 bm bd48e46 ef bd49e46 4.5v ef bd4845 gf bd4945 bk bd48e45 ee bd49e45 4.4v ee bd4844 ge bd4944 bh bd48e44 ed bd49e44 4.3v ed bd4843 gd bd4943 bg bd48e43 ec bd49e43 4.2v ec bd4842 gc bd4942 bf bd48e42 eb bd49e42 4.1v eb bd4841 gb bd4941 be bd48e41 ea bd49e41 4.0v ea bd4840 ga bd4940 bd bd48e40 dy bd49e40 3.9v dv bd4839 fv bd4939 bc bd48e39 dr bd49e39 3.8v du bd4838 fu bd4938 bb bd48e38 dp bd49e38 3.7v dt bd4837 ft bd4937 ba bd48e37 dn bd49e37 3.6v ds bd4836 fs bd4936 ay bd48e36 dm bd49e36 3.5v dr bd4835 fr bd4935 ar bd48e35 dk bd49e35 3.4v dq bd4834 fq bd4934 ap bd48e34 dh bd49e34 3.3v dp bd4833 fp bd4933 an bd48e33 dg bd49e33 3.2v dn bd4832 fn bd4932 am bd48e32 df bd49e32 3.1v dm bd4831 fm bd4931 ak bd48e31 de bd49e31 3.0v dl bd4830 fl bd4930 ah bd48e30 dd bd49e30 2.9v dk bd4829 fk bd4929 ag bd48e29 dc bd49e29 2.8v dj bd4828 fj bd4928 af bd48e28 db bd49e28 2.7v dh bd4827 fh bd4927 ae bd48e27 da bd49e27 2.6v dg bd4826 fg bd4926 ad bd48e26 cy bd49e26 2.5v df bd4825 ff bd4925 ac bd48e25 cr bd49e25 2.4v de bd4824 fe bd4924 ab bd48e24 cp bd49e24 2.3v dd bd4823 fd bd4923 aa bd48e23 cn bd49e23
datasheet 5/15 bd48xxx series bd49xxx series tsz02201-0r7r0g300030-1- 2 ? 2013 rohm co., ltd. all rights reserved. 22.may.2013.rev.008 www.rohm.com tsz22111 ? ? lineup - continued table 2. lineup for ssof3(1pin gnd) and ssop3(3pin gnd) package package type ssop3(1pin gnd) ssop3(3pin gnd) output type open drain cmos open drain cmos detection voltage marking part number marking part number marking part number marking part number 6.0v cm bd48k60 ff bd49k60 kb bd48l60 np bd49l60 5.9v ck bd48k59 fe bd49k59 ka bd48l59 nn bd49l59 5.8v ch bd48k58 fd bd49k58 hy bd48l58 nm bd49l58 5.7v cg bd48k57 fc bd49k57 hr bd48l57 nk bd49l57 5.6v cf bd48k56 fb bd49k56 hp bd48l56 nh bd49l56 5.5v ce bd48k55 fa bd49k55 hn bd48l55 ng bd49l55 5.4v cd bd48k54 ey bd49k54 hm bd48l54 nf bd49l54 5.3v cc bd48k53 er bd49k53 hk bd48l53 ne bd49l53 5.2v cb bd48k52 ep bd49k52 hh bd48l52 nd bd49l52 5.1v ca bd48k51 en bd49k51 hg bd48l51 nc bd49l51 5.0v by bd48k50 em bd49k50 hf bd48l50 nb bd49l50 4.9v br bd48k49 ek bd49k49 he bd48l49 na bd49l49 4.8v bp bd48k48 eh bd49k48 hd bd48l48 my bd49l48 4.7v bn bd48k47 eg bd49k47 hc bd48l47 mr bd49l47 4.6v bm bd48k46 ef bd49k46 hb bd48l46 mp bd49l46 4.5v bk bd48k45 ee bd49k45 ha bd48l45 mn bd49l45 4.4v bh bd48k44 ed bd49k44 gy bd48l44 mm bd49l44 4.3v bg bd48k43 ec bd49k43 gr bd48l43 mk bd49l43 4.2v bf bd48k42 eb bd49k42 gp bd48l42 mh bd49l42 4.1v be bd48k41 ea bd49k41 gn bd48l41 mg bd49l41 4.0v bd bd48k40 dy bd49k40 gm bd48l40 mf bd49l40 3.9v bc bd48k39 dr bd49k39 gk bd48l39 me bd49l39 3.8v bb bd48k38 dp bd49k38 gh bd48l38 md bd49l38 3.7v ba bd48k37 dn bd49k37 gg bd48l37 mc bd49l37 3.6v ay bd48k36 dm bd49k36 gf bd48l36 mb bd49l36 3.5v ar bd48k35 dk bd49k35 ge bd48l35 ma bd49l35 3.4v ap bd48k34 dh bd49k34 gd bd48l34 ky bd49l34 3.3v an bd48k33 dg bd49k33 gc bd48l33 kr bd49l33 3.2v am bd48k32 df bd49k32 gb bd48l32 kp bd49l32 3.1v ak bd48k31 de bd49k31 ga bd48l31 kn bd49l31 3.0v ah bd48k30 dd bd49k30 fy bd48l30 km bd49l30 2.9v ag bd48k29 dc bd49k29 fr bd48l29 kk bd49l29 2.8v af bd48k28 db bd49k28 fp bd48l28 kh bd49l28 2.7v ae bd48k27 da bd49k27 fn bd48l27 kg bd49l27 2.6v ad bd48k26 cy bd49k26 fm bd48l26 kf bd49l26 2.5v ac bd48k25 cr bd49k25 fk bd48l25 ke bd49l25 2.4v ab bd48k24 cp bd49k24 fh bd48l24 kd bd49l24 2.3v aa bd48k23 cn bd49k23 fg bd48l23 kc bd49l23
datasheet 6/15 bd48xxx series bd49xxx series tsz02201-0r7r0g300030-1- 2 ? 2013 rohm co., ltd. all rights reserved. 22.may.2013.rev.008 www.rohm.com tsz22111 ? ? absolute maximum ratings parameter symbol limits unit power supply voltage v dd -gnd -0.3 to +10 v output voltage nch open drain output v out gnd-0.3 to +10 v cmos output gnd-0.3 to v dd +0.3 output current io 70 ma power dissipation ssop5 *1*4 pd 540 mw ssop3 *2*4 700 vsof5 *3*4 210 operating temperature topr -40 to +105 c ambient storage temperature tstg -55 to +125 c *1 reduced by 5.4mw/c when used over 25c. *2 reduced by 7.0mw/c when used over 25c. *3 reduced by 2.1mw/c when used over 25c. *4 when mounted on rohm standard circuit board (70mm70mm1.6mm, glass epoxy board). electrical characteristics (unless otherwise specified, ta=-40 to 105c) parameter symbol condition limit unit min. typ. max. detection voltage v det r l =470k ? l *1 v det (t) 0.99 v det (t) v det (t) 1.01 v vdet=2.5v ta=+25c 2.475 2.5 2.525 ta=-40c to 85c 2.418 - 2.584 ta=85c to 105c 2.404 - 2.597 vdet=3.0v ta=+25c 2.970 3.0 3.030 ta=-40c to 85c 2.901 - 3.100 ta=85c to 105c 2.885 - 3.117 vdet=3.3v ta=+25c 3.267 3.3 3.333 ta=-40c to 85c 3.191 - 3.410 ta=85c to 105c 3.173 - 3.428 vdet=4.2v ta=+25c 4.158 4.2 4.242 ta=-40c to 85c 4.061 - 4.341 ta=85c to 105c 4.039 - 4.364 vdet=4.8v ta=+25c 4.752 4.8 4.848 ta=-40c to 85c 4.641 - 4.961 ta=85c to 105c 4.616 - 4.987 output delay time ?l h? t plh c l =100pf r ? 50% - - 100 s circuit current when on i cc 1 v dd =v det -0.2v ? ? (v det typ.+0.5v)
datasheet 7/15 bd48xxx series bd49xxx series tsz02201-0r7r0g300030-1- 2 ? 2013 rohm co., ltd. all rights reserved. 22.may.2013.rev.008 www.rohm.com tsz22111 ? ? electrical characteristics (unless otherwise specified, ta=-40 to 105c) - continued parameter symbol condition limit unit min. typ. max. ?low?output voltage (nch) v ol v dd =1.5v, i sink = 0.4 ma , v det =2.3-6.0v - - 0.5 v v dd =2.4v, i sink = 2.0 ma , v det =2.7-6.0v - - 0.5 ?high?output voltage (pch) (bd49exxx series) v oh v dd =4.8v, i source =0.7 ma, v det (2.3v to 4.2v) vdd-0.5 - - v v dd =6.0v, i source =0.9 ma,v det (4.3v to 5.2v) vdd-0.5 - - v dd =8.0v, i source =1.1 ma,v det (5.3v to 6.0v) vdd-0.5 - - leak current when off (bd48xxx series) i leak v dd =v ds =10v *1 - - 0.1 a detection voltage temperature coefficient v det / ? ? h l, r l =470k ?
datasheet 8/15 bd48xxx series bd49xxx series tsz02201-0r7r0g300030-1- 2 ? 2013 rohm co., ltd. all rights reserved. 22.may.2013.rev.008 www.rohm.com tsz22111 ? ? block diagrams fig.1 bd48xxx series fig.2 bd49xxx series
datasheet 9/15 bd48xxx series bd49xxx series tsz02201-0r7r0g300030-1- 2 ? 2013 rohm co., ltd. all rights reserved. 22.may.2013.rev.008 www.rohm.com tsz22111 ? ? typical performance curves fig.3 circuit current 0.0 0.5 1.0 1.5 2.0 0 1 2 3 4 5 6 7 8 9 10 v dd supply voltage
datasheet 10/15 bd48xxx series bd49xxx series tsz02201-0r7r0g300030-1- 2 ? 2013 rohm co., ltd. all rights reserved. 22.may.2013.rev.008 www.rohm.com tsz22111 ? ? typical performance curves C continued fig.7 operating limit voltage [v] 0.0 0.2 0.4 0.6 0.8 1.0 0 0.5 1 1.5 2 2.5 supply voltage : : : : v det [v] low to high(v det + ? v det high to low(v det
datasheet 11/15 bd48xxx series bd49xxx series tsz02201-0r7r0g300030-1- 2 ? 2013 rohm co., ltd. all rights reserved. 22.may.2013.rev.008 www.rohm.com tsz22111 ? ? typical performance curves C continued fig.11 operating limit voltage 0.0 0.5 1.0 1.5 -40 -20 0 20 40 60 80 100 temperature
datasheet 12/15 bd48xxx series bd49xxx series tsz02201-0r7r0g300030-1- 2 ? 2013 rohm co., ltd. all rights reserved. 22.may.2013.rev.008 www.rohm.com tsz22111 ? ? application information explanation of operation for both the open drain type (fig.12) and the cmos output type (fig.13), the detection and release voltages are used as threshold voltages. when the voltage applied to the v dd pins reaches the appropriate threshold voltage, the v out terminal voltage switches from either ?high? to ?low? or from ?low? to ?high?. please refer to the timing waveform and electrical characteristics for information on hysteresis. because the bd48xxx series uses an open drain output type, it is necessary to connect a pull-up resistor to v dd or another power supply if needed [the output ?high? voltage (v out ) in this case becomes v dd or the voltage of the other power supply]. fig.12 (bd48xxx series internal block diagram) fig.13 (bd49xxx series internal block diagram) reference data examples of leading (t plh ) and falling (t phl ) output part number t plh ( 5.1v v dd =5.1v 4.3v *these data are for reference only. the figures will vary with the application, so please check actual operating conditions before use. timing waveform example: the following shows the relationship between the input voltages v dd and the output voltage v out when the input power supply voltage v dd swept up and down (the circuits are those in fig.12 and 13). 1 when the power supply is turned on, the output is unstable from after over the operating limit voltage (v opl ) until t phl . therefore it is possible that the reset signal is not outputted when the rise time of v dd is faster than t phl . 2 when v dd is greater than v opl but less than the reset release voltage (v det + ? ? ?
datasheet 13/15 bd48xxx series bd49xxx series tsz02201-0r7r0g300030-1- 2 ? 2013 rohm co., ltd. all rights reserved. 22.may.2013.rev.008 www.rohm.com tsz22111 ? ? circuit applications 1) examples of a common power supply detection reset circuit. application examples of bd48xxx series (open drain output type) and bd49xxx series (cmos output type) are shown on the left. case1: power supply of the microcontroller (v dd2 ) differs from the power supply of the reset detection ic (v dd1 ). use an open drain output type (bd48xxx) device with a load resistance r l attached as shown in figure 15. case2: power supply of the microcontroller (v dd1 ) is same as the power supply of the reset detection ic (v dd1 ). use a cmos output type (bd49xxx) device or an open drain device with a pull up resistor between output and vdd1. when a capacitance c l for noise filtering is connected to the v out pin (the reset signal input terminal of the microcontroller), please take into account the rise and fall waveform of the output voltage (v out ). the electrical characteristics were measured using r l = 470k ? ( (
datasheet 14/15 bd48xxx series bd49xxx series tsz02201-0r7r0g300030-1- 2 ? 2013 rohm co., ltd. all rights reserved. 22.may.2013.rev.008 www.rohm.com tsz22111 ? ?
datasheet 15/15 bd48xxx series bd49xxx series tsz02201-0r7r0g300030-1- 2 ? 2013 rohm co., ltd. all rights reserved. 22.may.2013.rev.008 www.rohm.com tsz22111 ? ? operational notes 1) absolute maximum ratings operating the ic over the absolute maximum ratings may damage the ic. the damage can either be a short circuit between pins or an open circuit between pins. therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the ic is operated over the absolute maximum ratings. 2) ground voltage the voltage of the ground pin must be the lowest voltage of all pins of the ic at all operating conditions. ensure that no pins are at a voltage below the ground pin at any time, even during transient condition. 3) recommended operating conditions these conditions represent a range within which the expected characteristics of the ic can be approximately obtained. the electrical characteristics are guaranteed under the conditions of each parameter. 4) bypass capacitor for noise rejection to help reject noise, put a 1f capacitor between v dd pin and gnd and 1000pf capacitor between v out pin and gnd. be careful when using extremely big capacitor as transient response will be affected. 5) short between pins and mounting errors be careful when mounting the ic on printed circuit boards. the ic may be damaged if it is mounted in a wrong orientation or if pins are shorted together. short circuit may be caused by conductive particles caught between the pins. 6) operation under strong electromagnetic field operating the ic in the presence of a strong electromagnetic field may cause the ic to malfunction. 7) the v dd line impedance might cause oscillation because of the detection current. 8) a v dd to gnd capacitor (as close connection as possible) should be used in high v dd line impedance condition. 9) lower than the mininum input voltage puts the v out in high impedance state, and it must be v dd in pull up (v dd ) condition. 10) external parameters the recommended parameter range for r l is 10k ? ? ? ?
datasheet d a t a s h e e t notice - ge rev.002 ? 2014 rohm co., ltd. all rights reserved. notice precaution on using rohm products 1. our products are designed and manufac tured for application in ordinary elec tronic equipments (such as av equipment, oa equipment, telecommunication equipment, home electroni c appliances, amusement equipment, etc.). if you intend to use our products in devices requiring ex tremely high reliability (such as medical equipment (note 1) , transport equipment, traffic equipment, aircraft/spacecra ft, nuclear power controllers, fuel c ontrollers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (?specific applications?), please consult with the rohm sale s representative in advance. unless otherwise agreed in writing by rohm in advance, ro hm shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ro hm?s products for specific applications. (note1) medical equipment classification of the specific applications japan usa eu china class class class b class class class 2. rohm designs and manufactures its products subject to strict quality control system. however, semiconductor products can fail or malfunction at a certain rate. please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe desi gn against the physical injury, damage to any property, which a failure or malfunction of our products may cause. the following are examples of safety measures: [a] installation of protection circuits or other protective devices to improve system safety [b] installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. our products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditio ns, as exemplified below. accordin gly, rohm shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of an y rohm?s products under any special or extraordinary environments or conditions. if you intend to use our products under any special or extraordinary environments or conditions (as exemplified bel ow), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] use of our products in any types of liquid, incl uding water, oils, chemicals, and organic solvents [b] use of our products outdoors or in places where the products are exposed to direct sunlight or dust [c] use of our products in places where the products ar e exposed to sea wind or corrosive gases, including cl 2 , h 2 s, nh 3 , so 2 , and no 2 [d] use of our products in places where the products are exposed to static electricity or electromagnetic waves [e] use of our products in proximity to heat-producing components, plastic cords, or other flammable items [f] sealing or coating our products with resin or other coating materials [g] use of our products without cleaning residue of flux (ev en if you use no-clean type fluxes, cleaning residue of flux is recommended); or washing our products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] use of the products in places subject to dew condensation 4. the products are not subjec t to radiation-proof design. 5. please verify and confirm characteristics of the final or mounted products in using the products. 6. in particular, if a transient load (a large amount of load applied in a short per iod of time, such as pulse. is applied, confirmation of performance characteristics after on-boar d mounting is strongly recomm ended. avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading c ondition may negatively affect product performance and reliability. 7. de-rate power dissipation (pd) depending on ambient temper ature (ta). when used in seal ed area, confirm the actual ambient temperature. 8. confirm that operation temperat ure is within the specified range descr ibed in the product specification. 9. rohm shall not be in any way responsible or liable for fa ilure induced under deviant condi tion from what is defined in this document. precaution for mounting / circuit board design 1. when a highly active halogenous (chlori ne, bromine, etc.) flux is used, the resi due of flux may negatively affect product performance and reliability. 2. in principle, the reflow soldering method must be used; if flow soldering met hod is preferred, please consult with the rohm representative in advance. for details, please refer to rohm mounting specification
datasheet d a t a s h e e t notice - ge rev.002 ? 2014 rohm co., ltd. all rights reserved. precautions regarding application examples and external circuits 1. if change is made to the constant of an external circuit, pl ease allow a sufficient margin c onsidering variations of the characteristics of the products and external components, including transient characteri stics, as well as static characteristics. 2. you agree that application notes, re ference designs, and associated data and in formation contained in this document are presented only as guidance for products use. theref ore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. rohm shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. precaution for electrostatic this product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. please take proper caution in your manufacturing process and storage so that voltage exceeding t he products maximum rating will not be applied to products. please take special care under dry condit ion (e.g. grounding of human body / equipment / solder iron, isolation from charged objects, se tting of ionizer, friction prevention and temperature / humidity control). precaution for storage / transportation 1. product performance and soldered connections may deteriora te if the products are stor ed in the places where: [a] the products are exposed to sea winds or corros ive gases, including cl2, h2s, nh3, so2, and no2 [b] the temperature or humidity exceeds those recommended by rohm [c] the products are exposed to di rect sunshine or condensation [d] the products are exposed to high electrostatic 2. even under rohm recommended storage c ondition, solderability of products out of recommended storage time period may be degraded. it is strongly recommended to confirm sol derability before using products of which storage time is exceeding the recommended storage time period. 3. store / transport cartons in the co rrect direction, which is indicated on a carton with a symbol. otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. use products within the specified time after opening a hum idity barrier bag. baking is required before using products of which storage time is exceeding the recommended storage time period. precaution for product label qr code printed on rohm products label is for rohm?s internal use only. precaution for disposition when disposing products please dispose them proper ly using an authorized industry waste company. precaution for foreign exchange and foreign trade act since our products might fall under cont rolled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with rohm representative in case of export. precaution regarding intellectual property rights 1. all information and data including but not limited to application example contain ed in this document is for reference only. rohm does not warrant that foregoi ng information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. rohm shall not be in any way responsible or liable for infringement of any intellectual property rights or ot her damages arising from use of such information or data.: 2. no license, expressly or implied, is granted hereby under any intellectual property rights or other rights of rohm or any third parties with respect to the information contained in this document. other precaution 1. this document may not be reprinted or reproduced, in whol e or in part, without prior written consent of rohm. 2. the products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of rohm. 3. in no event shall you use in any wa y whatsoever the products and the related technical information contained in the products or this document for any military purposes, incl uding but not limited to, the development of mass-destruction weapons. 4. the proper names of companies or products described in this document are trademarks or registered trademarks of rohm, its affiliated companies or third parties.
datasheet datasheet notice ? we rev.001 ? 2014 rohm co., ltd. all rights reserved. general precaution 1. before you use our pro ducts, you are requested to care fully read this document and fully understand its contents. rohm shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny rohms products against warning, caution or note contained in this document. 2. all information contained in this docume nt is current as of the issuing date and subj ec t to change without any prior notice. before purchasing or using rohms products, please confirm the la test information with a rohm sale s representative. 3. the information contained in this doc ument is provi ded on an as is basis and rohm does not warrant that all information contained in this document is accurate an d/or error-free. rohm shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information.
datasheet part number bd4823fve package vsof5 unit quantity 3000 minimum package quantity 3000 packing type taping constitution materials list inquiry rohs yes bd4823fve - web page distribution inventory

▲Up To Search▲

Price & Availability of BD48K41G-TR

	To Download BD48K41G-TR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .